All Landmark timber components are selected for their long term suitability for outdoor use. Our timber structures are manufactured from LOSP treated select hoop pine as standard. Select hardwood timber is available as an optional extra on all Landmark standard products.
Ammoniacal Copper Quaternary is a more recent addition to the Australian preserved timber market. It is vaunted for its greater safety of storage and application than CCA, yet with similar performance ability. Ammoniacal Copper Quaternary (Type B) wood preservative is formulated with copper oxide and the Quaternary Ammonium compound, didecyldimethyl-ammoniumchloride.
Light Organic Solvent Preservatives are used for structures subject to moist environments where timber is likely to experience fungal decay. It is recommended that all treated timber is painted or stained. LOSP treated timber can be painted once the treatment has dried. The treatment is not corrosive to metals. LOSP is suitable for applications such as joinery, where dimensional-stability is important.
Timber components can be supplied in a water based paint finish as an optional extra. We apply two coats of quality Wattyl in our factory prior to despatch. Due to the likelihood of there being some damage during transport and installation we supply a small quantity of paint for touch up on site. You can check out the range of colours available here. Alternative paint finishes are available subject to pricing.
All timber components are factory stained with our Landmark Timbertone oil based timber stain as standard. Stained timber components are also available in the following range of colours on request, subject extended delivery times.
You can select timber wall cladding for our kit form restrooms from the following range of options:
Plantation Hoop Pine, stress grade MGP12, LOSP treated to hazard level 3, and factory stained in "Landmark Timbertone" as standard with a Hot Dipped Galvanised in-ground support or 316 grade stainless steel in-ground support as appropriate for the atmospheric conditions.
Plantation Hoop Pine, stress grade MGP12, LOSP treated to hazard level 3, and factory stained in "Landmark Timbertone" as standard
Our steel components are hot dipped galvanised as standard with optional powder coated finish to selected colour. Optional two pack epoxy paint is also available as appropriate for atmospheric conditions.
Steel components are available finished in a wide range of powder coated colours as standard.Click here to see the full range of colours.
Click here to see the full range of poly vinyl colour coatings.
A quality two pack epoxy paint system is available in a wide range of colours for steelwork used in corrosive marine environments.
All steel components are hot dip galvanised in accordance with Australian Standard AS1650 as standard. Hot dip galvanising is done after fabrication to ensure maximum durability and long life protection. The nature of the galvanising process leads to small bubbles in the galvanised surface .
Powder coated hot-dipped galvanised steel is considered an unsuitable finish for highly corrosive marine environments. In these environments we strongly recommend the use of timber (either hoop pine or hardwood) and stainless steel materials and components. If this is not possible all hot-dipped galvanised steel surfaces should at least be finished with a high quality two pack epoxy paint system.
For hot-dipped galvanised, powder coated and painted finishes both the appearance and lifespan of the finished metal surfaces will be greatly enhanced by periodic washing of all surfaces to prevent the build-up of corrosive agents. Particular attention should be paid to those areas under the roof line which are not subject to natural washing by wind-blown rain.
Hot dip galvanized and Powder-coated RHS, SHS or CHS steel (with curved aluminium braces on most designs) all with a powder coat finish. Optional 2 pack epoxy painted in lieu of powder-coat as appropriate for the atmospheric conditions. colours - anything from the Dulux Powder Coat range. Steel wall frames are galvanised channel.
Because of the difficulty in assessing accurately the corrosion potential of sites adjacent to marine environments, we strongly recommend that any steel structure within 1 km of marine environments be two pack epoxy painted and subjected to a rigorous maintenance schedule. Failure to do this in highly corrosive marine environments may void the Landmark Products Ltd Structural Integrity Warranty.
Sheeting is pre-cut colorbond custom orb, grade 'XRW', 'ULTRA', or 'STAINLESS STEEL' as appropriate for the atmospheric conditions complete with flashings and gutters if required.Available in:
Roof and wall cladding for our shelters and restrooms is available in the standard range of colorbond colours. See the range of colours available here...
Information regarding Maintaining COLORBOND® steel and ZINCALUME® steel is available here...
Colorbond stainless steel roofing is available for use in exposed seaside locations. Sheeting is pre-cut stainless steel colorbond custom orb in Surf Mist colour.
Doors for restrooms are covered with flat colorbond steel cladding in the standard range of colorbond colours. For exposed seaside locations, doors are available clad in stainless steel colorbond custom orb in Surf Mist colour.
Fixings are colour matched to colour selected for roof and wall as standard where possible.
Aluminium components are available finished in a wide range of powder coated colours as standard. Click here to see the full range.
Anodised aluminium can come in standard Clear or 3 other colour options: Olive Mist, Blue Night and Grey Smoke. Click here to see the range of colours.
Gang nail plates used for the trusses and portals are stainless steel. All screws are minimum Class 3 and Class 4 where available. All brackets and bolts are Hot Dipped Galvanised to AS 1650. Anti-vandal nuts are "Hollymetal" coated to a thickness of 45 microns. Optional 316 grade stainless steel for all the above as appropriate for the atmospheric conditions.
Stainless steel fixing upgrade together with colorbond stainless steel roofing available for exposed hazardous seaside locations.
From Landmark's factory to the site or designated depot.
Gazebo (6 sides standard or 8 sides optional), pavilion (4 sides pyramid), gable with overhangs, gable without overhangs, hip, marquee (extended gazebo), curved (steel roof frame only), wave (steel roof frame only), skillion, and optional cupola to suit gazebos or pavilions.
Flat, cranked or curved (steel beam or steel truss only) in both multi-span (with intermediate supports) and single span designs. Cable stayed designs are available for large single spans.
Pre-framed with flat colorbond steel cladding.
Pavilion (4 sides pyramid), gable with overhangs, hip, marquee (extended gazebo), curved (steel roof frame only), skillion.
Designed to suit both water flushing (sewer / septic) and alternative waste management systems (Landmark Products Ltd do not sell waste systems, we design our buildings to suit any type required by the client).
550 litre, colorbond rainwater tank with stand, plumbing, stainless steel basin and spring loaded vandal resistant tap or lever tap for disabled use. colorbond gutters with PVC downpipes to the rainwater tank.
Stainless steel or V/C pans with in-duct cisterns are available for sewer / septic (usually supplied by the client).
AS 1428.1-2001 "Design for Access & Mobility, Part 1". "Part 2" available on special request.
Landmark's products are supplied with a written Warranty to the effect that structures conform with relevant design and building codes, and meet or exceed the specified design criteria. Subject to various reasonable disclaimers, components are guaranteed to be free of defects, transit damage and faulty workmanship, and structural integrity is guaranteed for a period of 10 years.
Custom Orb
Mini Orb (wall cladding only)
Hardwood
Concrete
F.C. Sheeting
Internal:
External:
